hue lights home assistant

if its a 3rd party light that is just acting out all the time (shows as unavailable all the time in the hue app), it means the light is not able to route at all. in that case the light will jump to available (and stay that way) the first time you control it. if a light is unavailable in the hue app and ha it means that its a) powered off or b) having issues with connectivity, bad reception or c) not routing at all, such as most (all?) if a light is unavailable in the hue app and ha it means that its a) powered off or b) having issues with connectivity, bad reception or c) not routing at all, such as most (all?) are the lights that are reported as unavailable official hue lights ? @csanner what i’m trying to say is that it is not working correctly, as the hue app also lists the lights as unavailable.

next to being a huge asset for the ha community and the hue integration, marcel is one of the most helpful people around, always active and prepared to take the extra mile. i understand that the ha experience is technically correct and the hue setup is technically at fault. hue will show a small mark that a light is reported unavailable but will still allow you to control it while ha simply blocks control that a light that is unavailable ( the frontend, the service calls do still work). that way users have a way to workaround it (by simply toggling the light in the hue app or control the light (with an automation) through direct service call. the minute i enabled the setting to ignore unavailable all worked as normal. the negative side that you cannot see when the mesh is broken is not very important for a normal user.

sign up for a free github account to open an issue and contact its maintainers and the community. i still have my hue lights connected to bridge v2 wrongly reporting its state. my zigbee sensors state is connected and light entities report state as on but in fact they are off. (message by codeownersmention) ha showing the light on while the light is actually off. but when i try to turn off a light from ha, the light turns off, but the state remains on. for both the hue component and aiohue library. the 10 seconds is in fact applied to the entire connection and not only initial connect. you can set it back to zero for now to have a stable setup. in the meanwhile i’m going to think about the chicken and the again situation.

if i toggle a motion sensor switch in ha the state of the switch jumps back a few seconds later as the switch is reporting off in ha but is actually on in hue – therefore no push of state change from the bridge and no updating of the state in ha. i can force the issue to occur by simply toggling a motion sensor switch a few times in quick succession. you can temporary rollback to 2021.12.1 a fix will be on the way, thanks!! you can temporary rollback to 2021.12.1 a fix will be on the way, thanks!! simple math answers your question to “no, not fixed in 2021.12.2, yes it will be in a later (2021.12.3) release” btw a few posts above yours it is mentioned that rolling back to 2021.12.1 solves the issue, so the issue is introduced in 2021.12.2 @thefes the issue already existed in 2021.12.0 and 2021.12.1 but got worse in 2021.12.2. so a rollback to .1 will make things a bit better but not 100%. can you open a new issue and exactly describe what is not correct ? i doubt this is the same issue as referred to in the issue. state in the hue app is correct but its wrong at home assistant. you may want to enable debug logging to see a lot more info.

home assistant creates lights for each hue zone/room automatically but disables them by default. if you’d like to instructions on how to emulate a hue bridge within home assistant. i was wondering if anyone has experience with home assistant <> philips hue integration for a large installation (500+ hue accessories / bulbs)., philips hue lights, philips hue lights, philips hue bridge, home assistant hue motion sensor automation, home assistant hue scenes.

hi, i’m currently planning a smarthome setup and i have decided on philips hue lights. i’m wondering what’s the best way to connect them using a local api, home assistant core would simply ask the philips hue bridge what the state of any connected lights and sensors were. while the hue api allows you to group lights. home assistant also supports grouping of entities natively, but sometimes it can be usefull to use hue groups to, home assistant hue events, home assistant hue effects, home assistant emulated hue harmony, home assistant emulated hue setup.

When you try to get related information on hue lights home assistant, you may look for related areas. home assistant hue zigbee,home assistant hue without bridge,home assistant hue dimmer switch,home assistant hue color,home assistant hue lights unavailable philips hue lights, philips hue bridge, home assistant hue motion sensor automation, home assistant hue scenes, home assistant hue events, home assistant hue effects, home assistant emulated hue harmony, home assistant emulated hue setup.